How To Repair A Toilet Seat Hinge
Last Updated on May 18, 2022 by
A loose toilet seat is characterized by sideways movements as a event of loosening of the fixings that attach information technology to the toilet bowl. Loose toilet seats should exist tightened as soon as they start to wobble otherwise they will break.
Loose toilet seats are also a wellness hazard every bit they can result in falls particularly among the elderly and people with express mobility.
Toilet seats are attached to the toilet bowl using bolts, wingnuts and washers. The bolts are made up steel, brass or plastic. The elevation of the toilet seat fittings is usually curtained with plastic covers.
To tighten a toilet seat, grab the nut underneath the bowl using one hand and use the other hand to turn the mounting bolt clockwise using a screwdriver. To go on the seat aligned to the bowl, tighten the 2 bolts alternatingly just not as well much to prevent stripping them.
To tighten a toilet seat with concealed fixings, lift off the seat bolts covers using a finger or a screwdriver. Turn the bolts clockwise using the screwdriver but not too much lest you strip them or crack the bowl.
If the entire bolt is swiveling instead of tightening, dorsum off the nut on the underside of the bowl with your other mitt using a wrench. Mod toilet seats are easier to tighten since they are top-mounting and hence do not demand a nut.
Types of Toilet Seats
If y'all demand to know how to tighten a toilet seat, you lot must offset know the blazon of toilet seat you have. The post-obit are the different blazon of toilet seats you lot might come up beyond:
- Top fixing toilet seats
- Bottom fixing toilet seat
- Quick-release toilet seat
- Toilet seats with metallic bolts
- Toilet seats with plastic bolts
Pinnacle fixing and lesser fixing toilet seats are tightened the same manner. The only difference is that for top fixing seats you tighten the toilet seat hardware entirely from the top without bending over to admission the wingnuts nether the bowl. They are more mutual in skirted toilets.
Bottom fixing toilet seats are tightened by screwing in a wingnut and washer on a commodities from the underside of the toilet bowl while turning the bolt with a screwdriver from the top of the bowl.
To tighten a quick-release toilet seat, you start remove the seat by the press of a push or simply gently sliding information technology out. You so tighten the toilet seat mounting hardware so attach the seat.
Tightening each of the following is an like shooting fish in a barrel job and should not accept you more than than x minutes. Your toilet seat will go loose from fourth dimension to time and therefore learning how to tighten it will exist an invaluable lesson.
Tools Needed
- Flathead screwdriver
- Adjustable wrench
Let the states at present see how to tighten a toilet seat whether it has plastic bolts, metal bolts or curtained fixings.
How to Tighten a Toilet Seat
Stride 1: Observe the Bolts
A toilet seat is held in identify and secured to the toilet by 2 bolts at the back of the toilet basin. In most cases, the toilet seat bolts are concealed past plastic tabs.
The two tabs are colour-matched with the toilet seat for aesthetics but also importantly hold the seat in place and therefore prevents it from sliding. These tabs as well prevent h2o from getting into the bolts which then prevents them from corroding.
To access the bolts, pry off the tabs using a flathead screwdriver. There should be a slot to put in the screwdriver. Some tabs are designed in mode that you tin easily lift them off with your finger similar a bottle of lotion.
Step 2: Find the Wingnuts
The toilet seat bolts are used to tight the toilet seats past the use of nuts and sometimes washers. If the toilet seats has plastic bolts, and then the wingnuts are normally paw tight.
Toilet seats with metal bolts have nuts and washers and are adjusted using a flathead screwdriver and a wrench. Some metal bolts nevertheless apply wingnuts which do not need a wrench to tighten. Cheque your toilet seat advisedly.
In a top fixing type of toilet seat, at that place are no nuts. The toilet seat is tightened from the top either using a screwdriver or a drill machine with the correct bit size.
Step 3: How to Tighten a Toilet seat With Plastic Bolts
For a toilet seat with plastic bolts, you should always practice caution not to strip the commodities while tightening. One of the best ways to do this is to ensure you lot accept a big enough screwdriver to fit the bolt's groove.
Insert the screwdriver in the groove of the bolt caput but practice not turn. Attain for the bottom of the bowl and start turning the wingnut clockwise. Alternate between the two bolts. Practise not withal tighten besides much as this might strip out the plastic bolt.
But use the screwdriver to forbid the bolt from backing off only don't plow information technology. This might deform the groove and therefore render the bolt useless. If you take a hazard please change the plastic bolts with metal ones. Toilets with plastic bolts loosen more than often than ones with metallic bolts.
Footstep four: How to Tighten a Toilet with Metallic Bolts
A toilet seat with metallic bolts tin either exist a top-fixing blazon or a bottom fixing type. Top fixing toilet seats are easier and more comfy to tighten than lesser fixing toilet seats.
For a bottom fixing type of seat, you volition need to agree the nut at the bottom of the bowl and tighten the bolt using a screwdriver with your other mitt.
If the toilet seat uses metallic bolts with a metallic nuts and washers, you can use a wrench. Use an adjustable wrench to hold the nut in place, engage the screwdriver to the groove on top of the bolt and commencement turning the screwdriver clockwise.
On the other manus if the toilet seat uses metallic bolts and wingnuts, then hold the wingnut in your hand and tighten the bolt using the screwdriver with your other paw.
A skillful mode to make sure your toilet seat is tight evenly is to tighten both bolts alternatingly. If yous tighten ane at a time there is a chance the other side will lift off and information technology might be difficult to correct the get-go.
If y'all have a top fixing type of seat then your job is easy. You will only need to tighten the bolts with a screwdriver until you are satisfied that the seat is tight.
A word of caution especially when tightening a toilet seat with a wrench and screwdriver is to always be careful not to crack the toilet basin. The bowl is made of ceramic which cracks easily. Although our objective is to tighten the toilet seat, there y'all don't demand to go crazy on it.
Step 5: How to Tighten a Quick-Release Toilet Seat
A quick-release toilet seat is either a top fixing blazon or bottom fixing type. There are 2 types of quick-release toilet seats autonomously from how they are fixed.
Some quick-release toilet seats will just need to be slid out after removing the plastic tabs that covers the bolts. An instance of this is the Kohler quick-release toilet seats.
Other kind of quick-release toilet seats volition need to have the seat in the open position in to remove them. You will then push ane or two buttons so elevator if off. An case of such a toilet seat is the American Standard quick-release toilet seats.
To tighten a quick-release toilet seat, remove the plastic tabs covering the bolts to expose the toilet bolt head. If information technology is the bottom fixing type, concur the wingnut underneath the bowl with your hand and tighten the bolt using the screwdriver with your other manus.
To tighten a top fixing quick-release toilet seat, simply engage the screwdriver or drill automobile to the groove of the commodities and turn clockwise. For this type of seat, make sure the ii pins which are sticking out are aligned to the toilet seat earlier tightening.
Replacing the Toilet Seat Bolts
If while tightening your toilet seats you notice that the bolts are either damaged, stripped or rusted, the all-time matter to exercise is to replace them with new ones. A toilet seat tightening kit is an cheap and handy collection of toilet seat fixings that is amend than replacing the toilet seat.
FAQs
- How do you tighten a toilet seat on a skirted toilet?
A skirted toilet is a toilet with a concealed trapway. It therefore has no way of accessing the underside of the toilet basin to tighten the nuts. This toilet therefore uses pinnacle fixing toilet seats. To tighten a summit fixing toilet seat, remove the plastic tabs covering the toilet seat bolt to expose the head of the bolt. Employ a screwdriver to tighten the bolt (plough screwdriver clockwise)
two. Why is my toilet seat loose?
Toilet seat become loose due to the constant opening and closing every time a person uses the toilet. Slamming of the toilet seat on the toilet bowl too cause vibration on the bolts which then start to back off gradually.
iii. How practise you tighten a tiresome close toilet seat?
A wearisome close toilet seat is either a top fixing or bottom fixing type. To kickoff off, remove the plastic tabs that comprehend the head of the seat bolts. If it is a lesser fixing seat, concur the nut underneath the bowl with your hand and tighten the bolt with a screwdriver past turning clockwise.
If it is top fixing seat, it has no nuts under the bowl. Just tighten the bolt with a screwdriver. Earlier tightening the toilet seat in place make sure information technology is properly aligned to the bowl.
4. What should you do if your toilet seat commodities won't tighten?
There is a possibility that the bolt is stripped. In this example, the threads of the bolts accept been eaten away and tin therefore not tighten finer. The remedy to this is to purchase a toilet seat tightening kits that contains everything you lot volition need to tighten the toilet seat
5. How do y'all tighten a Vitra toilet seat?
A Vitra toilet seat is a tiptop fixing toilet seat. That means you only tighten information technology from above the toilet bowl and practice nothing underneath the bowl. Before tightening it yous should kickoff remove it. To remove the toilet seat, have it in the open position and remove the two argent caps on the hinge. Y'all tin can apply a flathead screwdriver for this.
Once the cups are out, lift off the toilet seat and identify it aside. On the top of the bowl you will see ii pins each with a argent cap at the bottom. Remove the caps to reveal the seat bolts. Use a screwdriver to tighten the bolts by turning it clockwise. Before tightening the bolts fully, ensure the toilet seat mounting holes are aligned to the two mounting pins.
One time the bolts are tight put the silver caps dorsum on and go ahead to fit the toilet seat.
Source: https://toilethaven.com/2020/03/21/how-to-tighten-a-toilet-seat/
0 Response to "How To Repair A Toilet Seat Hinge"
Post a Comment